Just How to Set up a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround
Just How to Set up a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround
Blog Article
What're your beliefs about A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't specifically brain surgery, however it does need strong plumbing, woodworking, and in some cases, tiling skills. Replacing an old bathtub with a new one is also a moderately hard task. If the old bathtub is conveniently easily accessible, the job can move quickly; if you have to open a wall surface to get rid of the old bathtub as well as position the new bathtub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will need a helper to move out the old bathtub and also embeded in the new one. Make sure you have certified yourself for the job and fit attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is better to take into consideration employing one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your restroom if you have actually currently purchased a brand-new bathtub and do not need to change the setup of your previous supply of water pipelines.
Your devices and product checklist should make up the following:
Preparing for the Installment
Firstly, the sustaining frame supplied with the bathroom ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps system to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be quite bothersome as a result of the limited accessibility that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the continuing to be water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Before moving on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using both wood boards under its feet, put the tub in the required position. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit all-time low of the furthest flexible tap connector to the ideal supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also inspect all joints and brand-new pipework for leakages as well as tighten them if required. Load the tub and additionally check the overflow electrical outlet as well as the regular electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and securing around the bathtub must wait until the bath tub has been made use of a minimum of when as this will resolve it into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin making certain that the washers remain in place between the faucet and the sink. Protect the faucet in place with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type must be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to problems with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are sold in tubes as well as cartridges, and also are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very involved in Tools You Need to Install a New Bathtub and I am hoping you enjoyed reading my post. Sharing is nice. Helping others is fun. We value reading our article about Tools You Need to Install a New Bathtub .
Book Your Installation
Report this page